AMERICAN WELDING SOCIETY


All types of Welding

Member # 769660
Since 1982
Certified Welding Inspector
Mike L. Porter, Sr.
AWS / CWI/ CWE
CWI # 02090241


Welder Certification Availiable
Per Applicable Codes
AWS D1.1, D1.2 D1.5, ASME IX etc.



 
Mike L. Porter
CWI 02090241
QC1 EXP. 9/1/2014
 

HomeContact UsRecently CertifiedLinksPrivacy Statement


Definition Quick Reference
  • WQTR
    • Welder Qualification Test Report
      • The WQTR describes the results of the welding test, including what the welder is qualified to do.
  • WPS
    • Welding Procedure Specification
      • The WPS describes the rules, welding parameters and details of the test or how the pieces should be assembled and welded. The WPS is like a blueprint or set of written instructions for the test.
  • WPQR
    • Welding Procedure Qualification Report
      • The WPQR documents the variables and test that have been performed by a qualified individual to prove the test is valid. The document and supporting information proves that the joint can be welded and tested to meet the specific Standard or Code requirements, the document if followed removes all variables except the skill of the welder. This document and its variables are used to construct the WPS.
  • WQR
    • Welder Qualification Record
  • PQR
    • Procedure Qualification Record
  • SMAW
    • Shielded Metal Arc Welding
  • GMAW
    • Gas Metal Arc Welding
  • FCAW
    • Flux Core Arc Welding
  • GTAW
    • Gas Tungsten Arc Welding
  • ASME IX
    • American Society Mechanical Engineers, Section 9
  • API
    • American Petroleum Institute
  • ASNT
    • American Society for Nondestructive Testing
  • D1.1
    • Structural Welding Code Steel
  • D1.2
    • Structural Welding Code Aluminum
  • D1.5
    • Bridge Code Welding/li>
  • D1.6
    • Structural Welding Code Stainless Steel









Welder Qualification And Certification

What is Certification?

     The term "Certification" as it applies to welders, refers to a document that states "I or We certify that" the indicated welder or welding operator has successfully completed a practical test of their abilities to perform a sound weld in accordance with some predetermined standard. The term "Qualification" means that a welder or welding operator has met the requirements of a given STANDARD, and is qualified to preform welds to within the scope of the STANDARD. To become CERTIFIED the welder must possess the skills necessary to produce a sound weld that is both visually acceptable, and that meets the testing requirements.

     The testing procedure involves the welder making a weld that is then tested by an inspector, to ensure that the weld conforms to a particular Code, Standard or written Welding Procedure Specification (WPS). Testing methods include visual inspection and may involve either destructive or non-destructive testing.

A simple test may involve the following steps:
  1. Ensure the proper safety equipment and welding supplies are present.
  2. Set the welding parameters, on the welding apparatus.
  3. Ensure the appropriate supplies are available.
  4. Obtain the appropriate supplies and materials to be welded.
  5. Prepare and assemble the joint to be welded.
  6. Place weld in the proper welding position.
  7. Follow the indicated procedure to fill the joint with weld.
  8. Prepare, or help prepare, the specimens to be tested.

     The Welding Inspector (Test Supervisor) will guide the preparations of the pieces, assembly and periodically check progress to ensure conformity to the Standard.

Fillet Weld Break Test
All Position Qualification


     The fillet weld break test is a simpler test that qualifies the welder to weld fillets with the process used during the test. To qualify all positions fillet welding, the welder must pass a separate break test in vertical and overhead positions.

     When the welder is only welding fillet welds as is often the case with GMAW (MIG) and GTAW (TIG) processes, a fillet weld break test in all positions instead of a groove test may be the only requirement for the job.

     To perform the test, the welder must weld a T joint on one side with a restart near the center as shown in the diagram above. The piece is visually examined and a macrotech test is conducted on one end of the piece. The piece is then broken to visually inspect for complete fusion and to ensure that there are no discontinuities according to the acceptance criteria of the code.

     To pass the visual examination prior to the break test, the weld shall present a reasonably uniform appearance and shall be free from overlap, cracks or excessive undercut, as defined by the Code. There shall be no porosity visible on the weld surface.

The broken specimen shall pass if:

  1. The specimen bends flat upon itself.
  2. The fillet weld, if not fractured, has a fractured surface showing complete fusion to the root of the joint, with no inclusion or porosity larger than 3/32 of an inch in greatest dimension.
  3. The sum of the greatest dimension of all inclusions shall not exceed 3/8 of an inch in the 6 inch long specimen.


Welder Certification Available
  • Mailing Address
    • 3008 Birch St. Bryant, AR 72019
  • E-mail Address
  • Home Number
    • (501) 847-2793
  • Cell Number
    • (501) 680-0588

Mike L. Porter
CWI 02090241
QC1 EXP. 9/1/2014

Copyright 2012 - All Rights Reserved - Mike L. Porter, Sr.